TIF takes aim at counterfeit hoisting grips and the shortcuts that drop lines off towers, killing tower techs

In Featured News by Wireless Estimator

A new Telecommunications Industry Foundation white paper warns that counterfeit and damaged hoisting grips have no place on a tower. The paper treats grips as permanent, load-bearing components that must match the cable, be documented in the rigging plan, and be scrapped after any overload.

The Telecommunications Industry Foundation (TIF) has released a white paper on one of the least glamorous components on a cell site — the hoisting grip. It doesn’t mince words: grips are permanent, load-bearing parts; counterfeits are in circulation; and a grip that has been shock-loaded or overloaded belongs in the scrap bin, not back on the line.

Safe and Compliant to Code and Standards Cable Hoisting Practices, published this month, was written by Marcus Ash, product manager for Heliax accessories, Andrew; Darin Piburn, chief operating officer of Rosenberger Site Solutions; and Scott Kisting, executive vice president of PTS Advisors. Its internal heading states the purpose more bluntly: “Beware of Unsafe Installation Practices and Counterfeit Products with hoisting grips in Wireless Infrastructure.”

The timing is hard to miss. In July, 5GT Towers foreman Eduard Shelipov, 31, a Ukrainian citizen, was killed in Castle Danger, Minnesota, when a transmission line fell and struck him on an American Tower structure. It was the industry’s first fatality of 2026, and Wireless Estimator noted that it closely resembled a 2022 death in which a hoisting grip holding a hybrid line failed.

That 2022 death, of a 32-year-old technician on a Verizon project in Weatherford, Texas, led NATE: The Communications Infrastructure Contractors Association to form a Hoisting Grip Task Team. The team drew subject-matter experts from contractors, tower owners, carriers, and manufacturers, and found no consensus standard for the design or use of wire mesh grips. In April 2023, it issued initial guidance, according to Wireless Estimator.

Plan it, document it, and buy the real thing

The paper builds its approach on ANSI/ASSP A10.48, the construction standard for communication structures, and asks contractors to plan cable work to at least its minimum requirements before anything leaves the ground. That plan should identify the competent person and the qualified person on the job, the structure and line types, the carrier and tower owner’s requirements, and the manufacturers’ instructions, and it should include grip locations, seating, attachment method, messenger use, and photos as part of the permanent site record.

On materials, the authors are direct. Grips should come from reputable manufacturers, with specification sheets confirming they are rated for the specific cable type and diameter. The paper warns that counterfeit and non-industry-specific grips may lack the testing, strength, tolerance, corrosion resistance, or fatigue performance the job demands.

And once a grip has taken a hit, it’s done. “Hoisting grips are permanent load-bearing components and should never be reused after overload or damage,” the authors write, adding that they know of no manufacturer that allows reuse after a load event. Rigging must not shock-load a grip in the first place.

The numbers crews will use

The paper gets specific. Using ANDREW guidance as an example, it cites maximum grip spacing of 200 feet, reduced to 150 feet for cables weighing about 2 pounds per foot. Evaluate messenger cables for vertical runs, especially those over 250 feet; the top grip seats first and takes the weight, then each lower grip takes its share until the line is off the messenger. Weight calculations should include the bends and loops at the top of the tower.

Cable hangers, typically fastened every 3 to 5 feet depending on hanger type, wind, ice, and manufacturer guidance, stabilize the line, not carry its weight. The authors discourage improvised or shared attachment points and recommend dedicated anchors on monopoles with J-hooks not designed for the load, on small-member guyed towers, and wherever multiple lines land at one elevation. On monopoles, grips need positive closure at the bottom to protect them from site activity.

The paper also spells out what a hoisting grip is not for: personnel lifting, lowering cable assemblies, supporting unintended loads, or any use outside its design criteria.

Guidance, not a standard

TIF is careful about what the document is. “THIS DOCUMENT IS NOT A STANDARD,” it states, and it does not supersede any statute, regulation or industry standard; TIF does not enforce, certify or test compliance. The foundation is seeking industry feedback through its website, where the paper is available alongside its earlier publications on ANSI/ASSP A10.48, job site safety, and its S.A.U.C.E. — Stop, Assess, Understand, Communicate and Engage — program.